Switch menu

Advanced Steam Injection Processes Training

From $5250 per attendee

Email Course Course PDF
Enquire About This Course In House Training

Available Courses

Course Information

  • Course Content
  • Course Description
  • Course Objectives
  • Who Should Attend
  • CPD Unit

Course Content

PART 1

Fundamental of Steam Injection Processes

  • Basic of Steam Injection
  • Steam Quality
  • Steam Injection Process
  • Steam Injection Process Mechanisms
  • Steam Distillation
  • Gas Stripping
  • In situ Solvent Drive
  • Viscosity reduction
  • Thermal Expansion
  • Solution Gas Drive
  • Gravity Segregation
  • Emulsion Drive
  • Cycle Steam Injection
  • Process Description
  • Mechanisms of Cycle Steam Process
  • References

 PART 2 

Criteria for Evaluating Steam Injection Prospects

  • Introduction
  • Rock and Fluid Properties
  • Pay Zone Thickness
  • Depth and Reservoir Pressure
  • Permeability and Transmissibility
  • Stratification
  • Anisotropy
  • Gas Cap or Aquifer
  • Dip Angle
  • Porosity
  • Oil Saturation
  • Clay Content
  • Crude Oil Characteristics
  • Gravity
  • Viscosity
  • Field History and Status
  • References

PART 3

Project Planning

  • Introduction
  • Reservoir Selection
  • Depth
  • Oil in Place
  • Reservoir Segregation and in-homogeneities
  • Preliminary Evaluation
  • Laboratory Analysis
  • Comprehensive Investigation
  • Comprehensive Performance Investigation
  • Comparison with Conventional Practices
  • Pilot Test
  • Summary
  • References

PART 4

Economic Of Steam Injection

  • Introduction
  • Economic Factors in steam Injection Operation
  • Estimation of Economically recoverable Oil
  • Stream Injection Project cost
  • Cost Estimate
  • Development Cost
  • Well Cost
  • Water Treatment
  • Summary
  • References

PART 5

Water Treatment for Steam Generation

  • Water for Steam Generation
  • Water Treatment Consideration
  • Total Hardness
  • Alkalinity
  • Oxygen
  • Sulfides
  • Total Dissolved solids
  • Total Suspended Solids
  • Iron
  • Oil
  • Silica
  • pH
  • Ion Exchange Unit Operation Problems
  • Resins stability
  • Varying Water Quality
  • Poor Operational Practices
  • Mechanical Problems
  • Ion Exchange Calculations
  • Hardness monitoring
  • Source Water Properties and Problems  of a Water system
  • Summary
  • General References

PART 6

Steam Generation

  • General features of Oil Field Steam Generators
  • Generator Selection
  • Design Requirements for Oilfield Steam Generators
  • Steam Gen0erator Components
    • Feed Water System
    • Feed Water Pre-heater
    • Fuel System
    • Combustion Air System
    • Convection  Section
    • Radiant section
  • Steam Generator Control
  • Process Description
  • Fuel System
  • Combustion Air System
  • Steam Generator Specifications
  • Fuel for Oil Field Generators
  • Natural Gas
  • Steam Generator operation and Problems
  • Tube failure
  • Other operation problems
  • Steam Generator Maintenance
  • Steam Generator Efficiency Calculations
  • Down Hole Steam Generator
  • Summary
  • References

PART 7

Steam Distribution

  • Introduction
  • Components of a steam distribution network
  • Main Steam Headers
  • Steam Flow rates and Pressure Drops
  • Expansion of Steam lines
  • Expansion of steam headers
  • Wellhead connections
  • Support of Steam Lines
  • Insulation and heat loss
  • Effect of branching on Steam Quality
  • Wellhead Equipment
  • Summary
  • References

PART 8

Steam Quality

  • Introduction
  • Surface Steam Quality Measurement
  • Separator Method
  • Orifice Metering Method
  • Total Dissolved Method
  • Electric Conductivity Method
  • Enthalpy Determination Method
  • Neutron Densitometer Steam Quality Measurement System
  • Summary
  • References

PART 9

Thermal Well Completion Practices

  • Introduction
  • Temperature effects on Casings and Tubings
  • Thermal Well Casing design
  • Tubing Strings Consideration
  • Thermal Well Completion
  • Cementing
  • Perforating
  • Openhole Gravel Packs
  • Consolidated packs
  • Suggested Steam Injection and Production well drilling and completion Procedures
  • DownHole Equipment
  • Packer Installation
  • Seal Systems
  • Summary
  • References

Course Description

Advanced Steam Injection Processes Training Course

Steam Injection is a thermal drive process that adds heat to the reservoir to expand the oil-in-place, reduce it viscosity, provide drive and thereby improve the displacement efficiency of injected fluid. This course explores the concepts behind steam injection processes in the field. The emphasis is the practical aspects of steam injection.  Equations and calculation methods are included in the course. There is an emphasis on the surface facilities, field practices, and operational problems. The material presented in this course is directed toward engineers, technicians, independent operators.

Course Objectives

  • Review and practice of Steam Injection processes.
  • Use and practice of Steam Thermal tables to calculate the injected energy in a steam injection well.
  • Steamflood Temperature and Saturation Profiles
  • Steam Injection Mechanisms
  • Cycle Steam Injection Processes
  • Criteria for evaluating Steam Injection Prospects
  • Estimated Heat Loss as function of depth
  • Steam Injection Project Planning
  • Economic of steam injection
  • Water Treatment for Steam Generation/Water Chemistry
  • Oilfield Steam Generator Water Quality Requirements
  • Steam Generation
  • Surface Steam Quality Measurement Concept and Methods
  • Thermal well Completion Practices
  • Thermal Cementing Practices

Who Should Attend

This course is designed for Petroleum Production and Reservoir Engineers and their supervisors; Chemical Engineers Associated with crude oil production in areas of high viscosity.  Technical field personnel and services companies representatives to obtain or increase the understanding of the overall concepts and principles of Steam Injection Processes.

CPD Unit

Continuing Professional Development

35 HOURS CPD

Related Courses

Reservoir Management Training

This course will address all the principles of reservoir management. The reservoir management process with integrated concept, role of reservoir simulation in reservoir management and importance of reservoir surveillance and monitoring for the whole reservoir management process will be discussed. The significance of the production optimization process in addition to the economics evaluation will be incorporated. The course covers all aspects related to hydrocarbon recovery methods starting from the primary recovery and up to enhanced oil recovery. The course will focus on different aspects of reservoir management applications for new reservoirs, matured reservoirs, reservoir with small gas caps, reservoir with huge gas caps, thin oil rims, reservoirs with new infill opportunities and fractured reservoirs.

4 locations available

Applied Reservoir Engineering Training

This course is designed to provide a solid understanding of the practical methods used in Reservoir Engineering for maximizing the ultimate hydrocarbon recovery. This course covers all aspects related to Reservoir Engineering during all reservoir life cycle, starting from the primary recovery and up to enhanced oil recovery. This course will address not only the conventional applications of Reservoir Engineering but also extends to include the topics of Reservoir Simulation Engineering. In order to support participants by a wide knowledge, special topics are included such as using conventional Reservoir Engineering techniques to identify new infill opportunities, coning control with smart horizontal wells, Fracture Reservoir Simulation and enhanced oil recovery modeling.

4 locations available

Reservoir Simulation Principles and Practices Training

This training course will provide a comprehensive coverage of the simulation key topics, challenges, pitfalls and the approach to a quality result. The participants will be trained in the methods and use of simulation software for practical exercises throughout this course.

3 locations available

Advanced Well Test Analysis Training

This five days short course will equip participants with the principles of advanced well test analysis to improve interpretation skills by developing key reservoir parameters from well pressure transient tests. Emphasis will also be placed on the importance of preparation; supervision of well tests; data retrieval; quality check; and interpretation methods; applicable to vertical and horizontal wells in homogeneous, layered, fractured, and compartmentalized reservoirs.  In addition, the application of state of the art interpretation classical and computer-aided methods will be described, supported with field examples for the different well test types such as drawdown, buildup, fall-off, interference, pulse, injection and DST’s. Interpretation methods: Horner, Log-Log, type curves, will also be illustrated with practical examples.

4 locations available

Thermal Recovery Methods for Heavy Oil Fields Training

This course is designed to cover all the traditional and modern Thermal Recovery Methods used in the oil industry for Heavy Oil recovery. Perhaps no other single subject dominates the oil industry like thermal recovery. For many of oil fields, particularly where low-to-medium gravity oils are found or where the oil viscosity is unfavourable for conventional EOR methods application, Thermal Recovery Methods are the best techniques for ultimate recovery. Vast deposits of heavy oil exist in Canada, Venezuela and USA that are amenable to recovery by Thermal Recovery. Thermal Recovery is usually applied to heavy to medium oils, however these methods can be applied to any field being considered and be competitive with alternative methods. The course consider the following methods: Cycle Steam Injection, Double Injection Nitrogen-Steam, CO2-Steam Injection, Flue Gas-Steam Injection-This methods have given excellent results in China and Louisiana (USA), Steam Drive Process, Hot Water Injection Processes, In Situ Combustion Processes, Cold Heavy Oil Production with Sand (CHOPS),  Vapor Extraction Method (VAPEX) and Steam-Assisted Drainage (SAGD).

4 locations available

Enhanced Oil Recovery Training

Upon completion of this training, participants will be able to select the enhanced recovery method that best suits the conditions of the reservoir which they operate and also maximise reservoir recovery at the least cost, ensuring maximum investment efficiency. Technical challenges of enhanced oil recovery phase; increasing complexity, cost/benefit consideration, facilities modifications and personnel training will be discussed. A critical review of the emerging technologies, future R & D directions will be devoted an extensive coverage. Participants will learn to forecast reservoir performance under various EOR methods employing the proper empirical, analytical, and simulation tools.

4 locations available

Oil Reserves Calculations Training

This course will give a full overview of all aspects of Reserves and Resource Volume estimation and reporting, including detailed technical calculation and forecasting, economic effects, commercial effects, and the impact on Corporate accounting. The various Reserves reporting authorities will be discussed along with examples of the impact of Reserves volumes on Corporate reporting.

4 locations available

Gas Condensate Reservoirs Training

This course enables participants to develop skills to analyse and manage gas condensate reservoirs. It addresses phase behaviour; relative permeability varying with velocity and interfacial tension; material balance equations; well productivity and pseudo-pressure calculation for different completion strategies, condensate banking and gravity drainage; practical fluid and flow simulation models.

4 locations available

Reservoir Engineering for Non-Reservoir Engineers Training

This reservoir engineering for non-engineers training short course is useful if you want to develop a feel for hydrocarbon behaviour in the reservoir and of various recovery methods. It also provides you with specific and direct application of the process used in reservoir engineering and enhances your skills in solving reservoir engineering problems and maximizing recoverable reserves.

3 locations available

Waterflooding and Chemical Flood Processes Training

The case for Waterflooding: Waterflooding is one of the most important methods of improving recovery from oil reservoirs. This section of the course concentrates on reservoir and field operations aspects of water injection for pressure maintenance and secondary recovery. Participants will study fractional displacement theory and all methods available in the oil & gas industry to predict oil recovery. The course is a theoretical practical course where participants have to work towards solving a series of projects, and to immediately apply the concepts, mathematical principles and theories presented and learned during the course. Laptop/computers will be used to solve problems related to waterflooding. The Case for Chemical Flooding: Valuable insight has been gained through chemical floods in the past – failures as well as successes. MP and ASP methods hold the greatest potential for commercial success; polymer flooding a third option. Chemical flooding processes must be re-evaluated under the current technical and economic conditions. Chemical floods offer the only chance of commercial success in many depleted and waterflooded reservoirs. Chemical flooding is here to stay because it holds the key to maximizing the reserves in our known reservoirs

4 locations available

Paraffin and Asphaltene in the Oil and Gas Industry: Physical Characteristics, Causes of Problems and Possible Solutions Training

This course discusses the physical characterization of crude oil, gas liquids and gas. Discussions of the causes of problems in all types of wells to include oil, gas, shale oil, coal bed methane, gas storage, injection, EOR produced wells and all types of surface equipment are included. The type of problems encountered in oils from 8 ° API to 90°API caused by paraffin and asphaltenes will be discussed. Field strategies for the production of these oils from these wells and practical solutions to produce these oils are presented. Testing methods for characterizing the physical characteristics of these oils and selecting possible treatment methods are covered. Discussions of current treatment methods, Mechanical, Thermal, Chemical and Others, to reduce or eliminate problems are included. A section will be included on effects of paraffin and asphaltenes on emulsion, corrosion and scale problems. A section on selecting Cost Effective treatment methods will be included. Formation damage removal of paraffin and asphaltenes from new and mature wells will be included. Questions will be taken throughout the course and discussion of the participants own problems will be encouraged. Laboratory and Field case histories are a large part of this course.

3 locations available

Waterflooding Technologies and Field Practices (N2/CO2/WAG) Training

This course concentrates on Reservoir and field operations aspects of waterfloooding injection for pressure maintenance and Secondary Recovery. Study in depth of Fractional Displacement theory and all methods available in the oil and gas industry to predict oil recovery. The course is a theoretical-practical course and is designed as a workshop where the participant has to work hard solving a series of projects to apply immediately the concepts, mathematical principles and theories presented and learned during the course. The participants will use a reservoir engineering software designed for water injection. The software will be provided to each participant without additional cost.

3 locations available

Re-Injection of Water Formation and Water Surface Treatment Technologies and Field Practices Training

This course is aimed at creating an understanding of WATER FORMATION RE-INJECTION AND WATER TREATMENT AND DISPOSAL. The course is designed to build up knowledge in the participant to understand the WATER RE-INJECTION process facilities design and Water treatment and disposal. The course studies in depth and in accordance to classic and new technology. Also the effect of Separation pressure is introduced using the engineering system concept of nodal analysis, and by using the classic flash calculations method. The calculations for pump specifications in the petroleum industry is treated in a formal and practical way.

3 locations available

Water Shut-Off and Conformance Improvement Technologies Training

Approximately 20 billion barrels of water are reinjected in the US every year. Any technology that minimizes the amount of water or gas produced in conjunction with the produced oil would have a significant impact on the energy consumption and on the cost oil production. There are many factors, such as the presence of thief zones or high permeability zones, fractures and water coning which lead to an increase in water production. In an attempt to block out the undesired water production and increase the volumetric sweep efficiency of on-going waterfloods, the industry has used crosslinked polymer gels. The process involves strategically injecting a Gelling fluid into water coning well or into a high permeability watered out zone, restricting flow in that zone and redirecting water flow into the lower permeability unswept oil zones. Thus water shut off and conformance-control treatments can be used to generate relatively large volumes of incremental oil production with low costs and selectively, targeted small volume treatments, which extends the economic lives of marginal and mature wells.

4 locations available

WAG-Water Alternating-Gas EOR Processes Training

Water alternating gas (WAG) injection are improved oil recovery methods that involve three-phase fluid flow. It was originally proposed as a method to improve the sweep efficiency of gas by using water to control the mobility ratio and to stabilize the front (Caudle and Dyes, 1958; Christensen et al., 1998). WAG injection can lead to improved oil recovery by combining better mobility control and contacting upswept zones, and by leading  to  improved microscopic displacement. WAG flooding has been successfully applied to more than 60 oilfields worldwide. This course will present WAG Miscible, WAG Immiscible, WAG alternating different types of Hydrocarbon Gases and Non-HC such as N2 and CO2 Gases. Also, the course will present and study the Factors Influencing Wag Process Design such as Fluid properties and rock-fluid, Availability and composition of injection gas, Heterogeneous Permeability, Injection Pattern, Capillary pressure, Relative permeability and Wettability. A WAG Process is presented and discussed in the course as well as Field cases and Laboratory research cases and results.

3 locations available

Development of Natural Gas Field Producer Training

This course is a theoretical-practical course designed to address the basic three stages in a gas field’s life: Reserves Determination, Development and Operation of the gas field. Before planning development of an optimum producing gas field, it is necessary to determine the total reserves of the gas field as accurate as possible. After this first step, It is necessary to determine the number of wells to develop the field based on the Gas Reserves, Reservoir Pressure, Reservoir fluids and Rock Properties, Gas Reservoir Dominant Mechanisms and Gas Demand.

3 locations available

Field Development Planning Training

This short course describes all the stages field development planning, starting with the basics of oil and gas exploration; the preliminary quantification and the appraisal activities; the data requirements and integration for preparation field development plan, including wells, reservoirs, production facilities, exporting options, environmental and government regulations.  The data preparation and documentation requirements for project sanction and implementation planning will also be covered, including practical exercises and field cases studies which will be used to illustrate the methodology. On this course, the alternative options available to develop hydrocarbon resources will also be discussed, the importance of developing and integrating associated costs in onshore and offshore environments will also be addressed. In addition, Subsea facilities and drilling components will be covered, and the key drivers to optimise costs and minimise risks will also be covered. Data management and integration will also be highlighted.

5 locations available

Petroleum Reservoir Engineering Training

The aim of this short course is to provide with necessary knowledge in oil and gas reservoir engineering that introduces evaluation techniques to define characters and properties of a petroleum reservoir and helps formulate engineering solution of petroleum field related problems. Numerous engineering practices are covered. This course will help the development of a more complete “understanding” of the characteristics of oil and gas reservoirs. Data collection, integration and application directed toward maximizing recovery are stressed. Reservoir engineering equations are introduced with emphasis directed to parameter significance and an understanding of the results.

5 locations available

Integrated Reservoir Modeling Training

Integrated Reservoir Modeling is carried out to better understand and characterize uncertainties in reservoir and well behaviour. It is used to make predictions for use in hydrocarbon development planning (field development planning) and well & reservoir surveillance and optimisation. This process should be seen in the context of a business plan for a new or producing asset in which a business focus will be maintained by addressing specifically those aspects having the biggest impact or influence on the business decisions being addressed. This course therefore, explicitly cover those aspects of a study in which the business context has a strong or dominating influence e.g. framing of the project, model design, economic screening and the selection of preferred development scenarios.

3 locations available
View all course categories

Accredited Oil & Gas training courses straight to your inbox

Mobility Oil and Gas will occasionally send you marketing material about training courses.

  • This field is for validation purposes and should be left unchanged.